Get total traffic visibility for 10/100/1000 monitoring and security devices by placing Net Optics 10/100/1000BaseT Taps on critical network links. 10/100/1000BaseT Taps support passive monitoring of 10/100/1000 links at 10, 100, or 1000 Mbps. This Tap is ideal when a passive Tap is required for use with a variety of copper monitoring devices.

For superior reliability, the 10/100/1000BaseT Tap features Link Fault Detect (LFD), which gives the devices connected to the Tap critical information about link status. If either side of the bi-directional link fails, the Tap immediately communicates the fault to both devices, reducing the time required to activate a redundant path.

Transparent Access

The 10/100/1000BaseT Taps establish permanent passive access ports without introducing a point of failure or disturbing other network connections. The 10/100/1000BaseT Tap either auto-negotiates communication or uses an external DIP switch to set fixed speed and duplexing parameters. These passive Taps deliver full-duplex monitoring with zero impact on network traffic around the clock.

Security and Visibility

Without an IP address, monitoring devices are isolated from the network, dramatically reducing their exposure to attacks. However, the monitoring device connected to the Tap still sees all full-duplex traffic as if it were in-line, including Layer 1 and Layer 2 errors.

Simply Plug It In

Full-duplex monitoring is a snap when each side of the signal is sent to a separate NIC on the monitoring device.  All network and monitoring cables necessary for plug-and-play deployment are included with the Tap.

Reliability

For extra uptime protection, Net Optics 10/100/1000BaseT Taps offer redundant power connections. Should the primary power source fail, the Tap automatically switches to the backup power source. Power LEDs on the front of the Tap indicate the current power source.

Operating Specifications:
Operating Temperature: 0°C to 55°C
Storage Temperature: -10°C to 70°C
Relative Humidity: 10% min, 95% max, non-condensing

Mechanical Specifications:
Power Supply:
Input: 100-240VAC, 0.5A ~ 47-63Hz
Output: 12V 1.5A

DC Power Input: -48 VDC typical, -36 VDC min, -75 VDC max
Dimensions: 1.125 high x 6.25 deep x 4.5 wide

Cable Interface:
Copper Cable Type: 22-24 AWG unshielded twisted pair cable, CAT5E
Link Distance Supported: 100 meters

Connectors:
(2) RJ45, 8 pin connectors (monitor ports)
(2) RJ45, 8 pin connectors (network ports)

Certifications:
Fully RoHS compliant

Part Numbers:
TP-CU3

Passive, Secure Technology

 

Provides passive access at 10/100/1000 Mbps without data stream interference or introducing a point of failure

Permanent in-line installation without affecting network performance

Link Fault Detect prevents undetected link failures

Passes all full-duplex traffic (including errors) from all layers for comprehensive troubleshooting

No IP address is needed for the Tap or monitoring device, enhancing monitoring security

Compatible with Power over Ethernet (PoE) applications

Redundant power ensures monitoring uptime

Fully IEEE 802.3 compliant

Fully RoHS compliant

Warranty

 

All Net Optics products come standard with a 1 year manufacturer's warranty

Optional 1 or 2 year extended warranty available at time of product purchase

 

Ease of Use

LED indicators show redundant power and link status

DIP switches select auto-negotiation of fixed speed and duplexing settings for the Tap

Front-mounted connectors make installation and operation quick and easy

All network and monitoring cables included

Silk-screened application diagram illustrates all connections for easy deployment

Optional 19-inch rack frame holds up to 3 or 12 Taps

Tested and compatible with all major manufacturers’ monitoring devices, including protocol analyzers, probes, and intrusion detection/prevention systems

Part Numbers

10/100/1000BaseT Tap

- TP-CU3
  Tap, Copper, 10/100/1G

- TP-CU3-DC
  Tap, Copper, 10/100/1G (-48V)

- RK-3V2
  3-Slot Rack Mount Frame

- RK-12V2
  12-Slot Rack Mount Frame

Net Optics - manufacturer of iTap™ - 10/100/1000 - GigaBit Network Taps, 10/100 - GigaBit Aggregator Taps, TX-SX, LX-SX All Converter Taps, IPS & IDS Bypass Switches, Matrix Switches and Teeny Tap™.

Resources

For more information, pricing, demonstration or evaluation on Net Optics Products please contact us here.

Questions? Call  1-805-277-2400