Net Optics GigaBit TX to SX Tap simplifies connecting SX fiber monitoring and security devices to GigaBit copper network links. Convert TX to SX and tap into the link with one device, reducing cost and complexity at the same time. GigaBit TX to SX Taps support passive monitoring of GigaBit links at 1000 Mbps.

For superior reliability, the GigaBit TX to SX Tap features Link Fault Detect which gives the devices connected to the Tap critical information about link status. If either side of the bi-directional link fails, the Tap immediately communicates the fault to both devices, reducing the time required to activate a redundant path.

Transparent Access

GigaBit TX to SX Taps establish permanent passive access ports without introducing a point of failure or disturbing other network connections. These passive Taps deliver full-duplex monitoring with zero impact on network traffic around the clock.

Security and Visibility

Without an IP address, monitoring devices are isolated from the network, dramatically reducing their exposure to attacks. However, the monitoring device connected to the Tap still sees all full-duplex traffic as if it were in-line, including Layer 1 and Layer 2 errors.

Simply Plug It In

Full-duplex monitoring is a snap with supplied cables. All network and monitoring cables necessary for plug-and-play deployment are included with the Tap. Everything you need, right out of the box.

Reliability

For extra uptime protection, Net Optics GigaBit TX to SX Taps offer redundant power connections. Should the primary power source fail, the Tap automatically switches to the backup power source. Power LEDs on the front of the Tap indicate the current power source – even if power is lost and reapplied, there is always zero delay to network traffic.

Fiber Type: Multimode Corning 62.5/125µm, wavelength 850nm
Insertion Loss: Monitor Port: 4.5 dB

Copper Cable Type: 22-24 AWG unshielded twisted pair cable, CAT5/CAT5E
Link Distance Supported: 100 meters

Operating Specifications:
Operating Temperature: 0°C to 55°C
Storage Temperature: -10°C to 70°C
Relative Humidity: 10% min, 95% max, non-condensing

Mechanical Specifications:
Power Supply: 
Input: 100-240V, 0.5A, 47-63Hz
Output: 12V, 1.5A
Dimensions: 1.125" high x 6.5" deep x 4.5” wide

Connectors:
(1) Duplex LC connector (monitor port)
(2) RJ45, 8 pin connectors (network ports)

Fiber Optic Interface:
Connectors: Class I, eye-safe, laser emitter type. These Class I Lasers conform to the applicable requirements per US 21 CFR (J), EN 60825-1, and UL 1950 applications.
Optical Transmitter Wave Length: 850 nm nominal
Output Power: -9.5 dB min, -4 dB max
Optical Receiver Input Sensitivity: 0 dB min, -17 dB max

Certifications:
Fully RoHS compliant

Part Number:
CVT-GCU/SX

Passive, Secure Technology

 

Provides passive access at 1000 Mbps without data stream interference or introducing a point of failure

Link Fault Detect prevents undetected link failures

Access GigaBit copper links with SX fiber devices without a separate converter

Permanent in-line installation without affecting network performance

Passes all full-duplex traffic (including errors) from all layers for comprehensive troubleshooting

No IP address is needed for the Tap or monitoring device, enhancing monitoring security

Redundant power ensures monitoring uptime

Fully IEEE 802.3 compliant

Fully RoHS compliant

Warranty

 

All Net Optics products come standard with a 1 year manufacturer's warranty

Optional 1 or 2 year extended warranty available at time of product purchase

 

Ease of Use

LED indicators show redundant power and link status

Front-mounted connectors make installation and operation quick and easy

Silk-screened application diagram illustrates all connections for easy deployment

All network and monitoring cables included

Optional 19-inch rack frames hold up to 3 or 12 Taps

Tested and compatible with all major manufacturers’ monitoring devices, including protocol analyzers, probes, and intrusion detection/prevention systems

Part Numbers

GigaBit Fiber TX to SX

- CVT-GCU/SX
  Converter, Tap, 1G, Copper
  to SX 62.5µm,  LC

- RK-3V2
  3-Slot Rack Mount Frame

- RK-12V2
  12-Slot Rack Mount Frame

Net Optics - manufacturer of iTap™ - 10/100/1000 - GigaBit Network Taps, 10/100 - GigaBit Aggregator Taps, TX-SX, LX-SX All Converter Taps, IPS & IDS Bypass Switches, Matrix Switches and Teeny Tap™.

Resources

For more information, pricing, demonstration or evaluation on Net Optics Products please contact us here.

Questions? Call  1-805-277-2400